KC778B DATASHEET PDF

COMedia KCB datasheet, Master PIR Control Chip (6-page), KCB datasheet, KCB pdf, KCB datasheet pdf, KCB pinouts. KCB Datasheet, KCB PDF, KCB Data sheet, KCB manual, KCB pdf, KCB, datenblatt, Electronics KCB, alldatasheet, free, datasheet. KCB datasheet, cross reference, circuit and application notes in pdf format.

Author: Bajar Jurr
Country: Ukraine
Language: English (Spanish)
Genre: Video
Published (Last): 26 April 2006
Pages: 320
PDF File Size: 7.59 Mb
ePub File Size: 18.26 Mb
ISBN: 291-6-66929-761-8
Downloads: 52071
Price: Free* [*Free Regsitration Required]
Uploader: Dom

Due to its high sensitivity and. The filter response can be measured in this way. Load turns off if there is no motion during the time delay. If the load goes off because you stopped moving reading a book for exampleyou have 6 seconds to wave your arm to turn the load back on.

Load turns on when motion is detected adjustable sensitivity. This node should also be closely surrounded by a ground plane. Load turns on manually, with a momentary contact switch. I Daylight detector circuitry is designed to use either silicon photo diode or CdS detector. The value of the pot is not critical and any value between The Sensitivity Adjust pot is used to select a voltage between the pyro drain reference voltage minimum.

Pin 8 Pyro S is a sensitive node and the external interconnect to this pin should be made as short as. Auto-OFF mode can be disabled. E Adjustable PIR sensitivity. C High sensitivity PIR input with special noise cancellation circuitry.

The Sensitivity Adjust pot is used to select a voltage between the pyro drain reference voltage minimum sensitivity and Gnd maximum sensitivity. If the load goes off because you stopped moving reading a book for.

  ADIOS HEMINGWAY LEONARDO PADURA PDF

F Internal switched capacitor bandpass filter reduces external component count and improves reliability by. Load turns off manually, with a momentary contact switch. Load turns on manually, with a momentary contact switch. J Adjustable daylight detector sensitivity. H High immunity to line frequency noise.

PDF KC778B Datasheet ( Hoja de datos )

Load turns off if there is no motion during the time delay. Daylight detector can be disabled. A ,c778b design maximizes performance while minimizing external component count and board layout space. If Auto-ON mode is disabled, the load will turn on if there is motion within 6 seconds after turn-off.

Adjustable OFF timer activates whenever motion stops.

A Circuit design maximizes performance while minimizing external component count and board layout space. If the load goes off because you stopped moving reading a book for. D Choice of two PIR gain settings: If the daatasheet goes off because you stopped moving reading a book for exampleyou have 6 seconds to wave your arm to turn the load back on.

KC778B Datasheet PDF

Adjustable OFF timer k778b whenever motion stops. M Four main operating modes can kc778b used in any combination: The MPCC has been designed for easy implementation. Disconnecting the external capacitor prevents motion from being detected. D Choice of two PIR gain settings: F Internal switched capacitor bandpass filter reduces external component count and improves reliability by. If Auto-ON mode is disabled, the load will turn on if there is motion within 6 seconds after turn-off.

  C114 DATASHEET PDF

The MPCC has been designed for easy implementation. Auto-ON mode can be disabled. C High sensitivity PIR input with special noise cancellation circuitry.

Ozitronics – Security

Due to its high sensitivity and. I Daylight detector circuitry is designed to use either silicon photo diode or CdS detector.

K Adjustable OFF kc778h accuracy is determined by external components.

J Adjustable daylight detector sensitivity. H High immunity to line frequency noise. E Adjustable PIR sensitivity. Adjustable daylight detector disables Auto-ON during daytime. B Low cost solution for PIR motion control switching applications.

F Internal switched capacitor bandpass filter reduces external component count and improves reliability by minimizing sensitivity to external component values. The output of the switched capacitor bandpass filter can be seen on pin 3 Offset Filter when the external.

If Auto-ON mode is disabled, the load will turn on if there is motion within 6 seconds. Auto-OFF mode can be disabled. M Four main operating modes can be used in any combination: Due to its high sensitivity and reliability, it is also widely used in security product.

K Adjustable OFF timer accuracy is determined by external components. Load turns off manually, with a momentary contact switch.